A Large Variety of Desktop E-Nail Kits, Portable E-Nails, Quartz Nails, Titanium Nails, and Accessories. One Year Warranty, Ships in 24 Hours. 710 your life!

Discount E-Nails

Dabbing

Vaping

Smoking

Crossing TUG E-Rig Kit
The Tug E-rig is a new portable dab rig from Crossing Tech which has been designed to be super user friendly and simple to use, much like the Core 2.0 but at an even more wallet friendly price! It comes with everything required to get dabbing (except the dabs) and makes use of a single button which controls everything!

Also included with the TUG is a ceramic 3D heated chamber with heating elements inside the base and the sides of the ceramic, this helps the Tug produce thick clouds of tasty vapor with minimal effort. The TUG heater also has taller than usual side walls which help contain the concentrate inside the heated cup and allow for both more powerful inhales and a wide range of compatible carb caps, in case you prefer to use an existing one over the provided carb cap.

The TUG is an ideal entry level rig but is also well suited to experienced dabbers who want something which "just works!". Making use of a variable voltage heating system with haptic feedback to let you know when the session is reached, there is only a small learning curve for this device.

Features

One button functionality for ease of use
3D Heated high polish ceramic vaping surface
Replaceable atomizer
Vortex Airflow - Aluminum spinner carb cap with carb cap tether
Borosilicate Glass Bubbler
Four carefully tuned heat settings
Glass and Silicone Vapor Pathway
Low maintenance
Approx. 1 hour 45 minute charging time
2700mah Li-Ion Battery Pack
Approx. 16 full sessions - mixed power settings
Under-Lit Bubbler LED
Feedback Free Bubbler


Setup

Always hold your e-rig upright! If you angle it during use concentrate will spill out the bucket! Now that's out the way...
Charge your base using the provided wall plug and cable.
Fill the bubbler from the top, when it is removed from the base. Ensure any excess liquid has been wiped away.
Do not fill the bubbler past the bottom third.
Place bubbler onto TUG Base then gently and firmly push it straight down into place so that the sucker seals onto the bottom.
Select your desired heat setting (start low if you're not sure).
Now that's all done we get onto the vaping methods as there are different ways the TUG E-rig can be used! (yes we copied this next section from the Core 2.0 page as the vaping instructions are identical!)

Crossing Tug E-Rig Kit

Crossing Core 2.0 E-Rig Kit
The one you've been waiting for... Core 2.0 e-rig with a black silicone sleeve and carb tether, 4-port spinner carb cap and V5 Heater!! 
When heater housing design and art combines! Meet the new rebuildable ceramic coil for the Core 2.0 E-Rig. The RDA V5 Ceramic Heater works on the original Core also. The original Core coil atomizers work on the Core 2.0 too! 
  
There are a some key differences between the Core and Core 2.0 e-rigs which are as follows: 
 
Core 2.0 runs V5 heaters, no wire based coils 
Atomizers contain only Metal and Ceramic, silicone and PEEK has been replaced with an all ceramic design 
Four heat settings are now all for the V5 heaters 
Fully rebuildable atomizers – no need to replace the whole housing, just the heater 
Decreased pre-heat time 
Increased session time 
Increased total run time (80 second full run time) 
Vortex airflow – included spinner carb cap 
“Unbreakable” aluminum carb cap replaces glass bubble carb 
Improved button function 
Upgraded Stainless Steel Carb Cap Tube 
 
 
Features 
 
One button functionality for ease of use 
Fully heated high polish ceramic vaping surface – elements inside base and walls of heater 
Rebuildable atomizer 
Vortex Airflow – Aluminum spinner carb cap with carb cap tether 
Borosilicate Glass Bubbler 
Stainless Steel Carb Cap Tube 
Four carefully tuned heat settings 
Isolated Aluminum and Glass Vapor Pathway 
Low maintenance 
Approx. 1 hour 45 minute charging time 
3150mah Li-Ion Battery Pack. 
 
 
What’s Included 
 
Core 2.0 E-rig Base 
Core Bubbler 
Aluminum Spinner Carb Cap (based on our design) 
Carb Cap Tether (black) 
Silicone Base Cover/Sleeve (black) 
Atomizer with V5 heater installed 
Spare V5 Heater 
SS316 Dab Tool (based on our design) 
4 x Spare Atomizer Screws 
Screwdriver 
2 x Spare Carb Cap Tube O-rings 
1 x Wall Plug – US inside – UK included for UK orders 
1 x USB-C Charging Cable 
Cotton buds/Q-tips 
Alcohol wipes 
Upgraded Carry Case 
 
 
Button Functions 
 
Hold – Manual fire up to 60 seconds 
Two clicks – Activate session mode – One click to cancel 
Three Clicks – Change heat setting 
Four Click – Display power level – Red/Low – White/Medium – Green/Full 
Five Clicks – Lock or unlock Core 2.0 Base 
 
 
Sessions times and temperatures 
 
The total session time for the Core 2.0 has been upgraded to 80 seconds, this includes the pre-heat time. 
 
Blue – 12.5 second pre-heat – Approx. 400° 
Green – 13 second pre-heat – Approx. 425° 
White – 17.5 second pre-heat – Approx. 465° 
Red – 22.5 second pre-heat – Approx. 500° 
 
 
Setup 
 
Charge your base using the provided wall plug and cable. 
Fill the bubbler from the top, when it is removed from the base. Ensure any excess liquid has been wiped away and that no water has flooded into the bottom compartment. If this happens turn the bubbler upside down and blow into the air hole at the bottom to clear this section. Then re-fill from the top. 

Place bubbler onto Core 2.0 Base at an angle, ensuring that the hole in the bubbler base aligns with the vapor pathway in the Core 2.0 base, then gently and firmly push it straight down into place. 

Check small screws in the atomizer base which hold the heater legs are done up fully. These need to be tightened so they are firm, but not so much that they cut the wire legs off the heater. When this is done screw the atomizer into the Core 2.0 base. 

Place the carb cap tube on the base so that the wider angled side sits at the top, leaving the carp cab on the tether so that you can load concentrate onto the heater. 
Select your desired heat setting (start low if you’re not sure). 

Now that’s all done we get onto the vaping methods as there are different ways the Core 2.0 can be used! 
 
 
Methods of Use 
 
Cold Starts – This method is best for getting the most flavor and material preservation as you start using as soon as vapor is being produced. Using it in this way will cause the session temperatures to be slightly lower than otherwise because the air passing around the heater will decrease heating speed. You can start your session at any point, we suggest keeping an eye on the button flashes so that you can always begin after a set number of flashes, if desired, providing a very consistent and repeatable experience. 
 
Load material into the heater 
Press the fire button twice to activate session mode 
When your concentrate starts to bubble begin using gently with the carb cap left off 
When the Core 2.0 base vibrates place the carb cap back on and continue your use as you normally would 
For subsequent sessions just use as desired, when the flavor leaves your material, the vapor becomes harsh or stops being produces press the fire button once more to cancel the session 
If you still have material left inside at the end of the session simple hit the fire button twice again and start using immediately, no need to wait for the vibrate as your heater will already be close to adequate temperature. The second session will always run a little hotter than the first if it is started straight after 
Hot Starts –  This way allows the heater to reach full temperature for any given setting; so this method is best for getting the maximum cloud production and effects as quickly as possible. 
 
Press the power button twice to activate session mode 
Load your material onto your dab tool – rice size 
Wait for the Core 2.0 base to vibrate indicating the session temperature has been reached 

While using gently load the dab into the heater, then replace the carb cap and use as your normally would

For subsequent sessions you can carry on as desired. The same applies here with regard to finishing your session. If your material is finished hit the fire button once to cancel the session early, if you still have material left simply hit it twice when the session has ended to start it again! 

As with cold starts, follow up sessions will always run a little hotter. 
Manual – Self explanatory, load a small rice size dab into the heater and hold down the power button. Use as desired. 
 
Manual hold can also be used instead of double pressing to finish a session or heat the heater for easier cleaning. 
 
 
 
Cleaning 
 
Wipe out heater with a Q-tip after each use 
Clean the area around the RDA heater weekly to stop residue building up 
Every month or so wipe out the airway with a Q-tip soaked in ISO – allow to fully dry before use 
Replace bubbler water daily 
To clean bubbler fill with hot water and shake to remove large residues. Soak in ISO to fully clean. Rinse thoroughly with warm water after soaking. 
 
 
Safety Features 
 
Over-charge 
Over-discharge/Low battery 
Over-heat 
Low heater resistance 
Short-circuit 
No atomizer 
 
 
Certifications 
 
CE Certified 
ROHS Certified Materials 
FCC Certification 
FDA Approved Silicone 
UN 38.3 Certified Li-Ion Battery Pack. 
Warning Lights – When your Core 2.0 base flashes three times it’s trying to tell you something… 
 
Blue – Short-circuit warning 
Green – No atomizer warning 
White – Over-heat warning 
Red – Low battery warning 
  
Warranty information 
 
For all warranty claims please contact the store you purchased from. 
The Core 2.0 power base is covered by a one year manufacturer warranty against defects. 
The Core 2.0 carry case is covered by a one year manufacturer warranty against defects. 
The atomizer is covered by a one week manufacturer warranty against defects. 
While atomizers are expected to last much longer than one week, they can be damaged by mishandling and misuse. We understand that not everyone will use the device daily or immediately so offer a one week warranty, from the date of delivery, to report any issue with your atomizer. 

Crossing Core 2.0 E-Rig Kit

Crossing Core 2.0 | 2.1 Stargazer Side-Mouthpiece Bubbler E-Rig Kit
Model Choice: 2.0 or 2.1

The one you've been waiting for... Core 2.0 e-rig with a black silicone sleeve and carb tether, 4-port spinner carb cap and V5 Heater!! 
When heater housing design and art combines! Meet the new rebuildable ceramic coil for the Core 2.0 E-Rig. The RDA V5 Ceramic Heater works on the original Core also. The original Core coil atomizers work on the Core 2.0 too! 
  
There are a some key differences between the Core and Core 2.0 e-rigs which are as follows: 
 
Core 2.0 runs V5 heaters, no wire based coils 
Atomizers contain only Metal and Ceramic, silicone and PEEK has been replaced with an all ceramic design 
Four heat settings are now all for the V5 heaters 
Fully rebuildable atomizers – no need to replace the whole housing, just the heater 
Decreased pre-heat time 
Increased session time 
Increased total run time (80 second full run time) 
Vortex airflow – included spinner carb cap 
“Unbreakable” aluminum carb cap replaces glass bubble carb 
Improved button function 
Upgraded Stainless Steel Carb Cap Tube 
 
 
Features 
 
One button functionality for ease of use 
Fully heated high polish ceramic vaping surface – elements inside base and walls of heater 
Rebuildable atomizer 
Vortex Airflow – Aluminum spinner carb cap with carb cap tether 
Borosilicate Glass Bubbler 
Stainless Steel Carb Cap Tube 
Four carefully tuned heat settings 
Isolated Aluminum and Glass Vapor Pathway 
Low maintenance 
Approx. 1 hour 45 minute charging time 
3150mah Li-Ion Battery Pack. 
 
 
What’s Included 
 
Core 2.0 E-rig Base 
Core Stargazer Side-Mouthpiece Bubbler 
Aluminum Spinner Carb Cap (based on our design) 
Carb Cap Tether (black) 
Silicone Base Cover/Sleeve (black) 
Atomizer with V5 heater installed 
Spare V5 Heater 
SS316 Dab Tool (based on our design) 
4 x Spare Atomizer Screws 
Screwdriver 
2 x Spare Carb Cap Tube O-rings 
1 x Wall Plug
1 x USB-C Charging Cable 
Cotton buds/Q-tips 
Alcohol wipes 
Upgraded Carry Case 

-(No factory glass bubbler included)-
 
 
Button Functions 
 
Hold – Manual fire up to 60 seconds 
Two clicks – Activate session mode – One click to cancel 
Three Clicks – Change heat setting 
Four Click – Display power level – Red/Low – White/Medium – Green/Full 
Five Clicks – Lock or unlock Core 2.0 Base 
 
 
Sessions times and temperatures 
 
The total session time for the Core 2.0 has been upgraded to 80 seconds, this includes the pre-heat time. 
 
Blue – 12.5 second pre-heat – Approx. 400° 
Green – 13 second pre-heat – Approx. 425° 
White – 17.5 second pre-heat – Approx. 465° 
Red – 22.5 second pre-heat – Approx. 500° 
 
 
Setup 
 
Charge your base using the provided wall plug and cable. 
Fill the bubbler from the top, when it is removed from the base. Ensure any excess liquid has been wiped away and that no water has flooded into the bottom compartment. If this happens turn the bubbler upside down and blow into the air hole at the bottom to clear this section. Then re-fill from the top. 

Place bubbler onto Core 2.0 Base at an angle, ensuring that the hole in the bubbler base aligns with the vapor pathway in the Core 2.0 base, then gently and firmly push it straight down into place. 

Check small screws in the atomizer base which hold the heater legs are done up fully. These need to be tightened so they are firm, but not so much that they cut the wire legs off the heater. When this is done screw the atomizer into the Core 2.0 base. 

Place the carb cap tube on the base so that the wider angled side sits at the top, leaving the carp cab on the tether so that you can load concentrate onto the heater. 
Select your desired heat setting (start low if you’re not sure). 

Now that’s all done we get onto the vaping methods as there are different ways the Core 2.0 can be used! 
 
 
Methods of Use 
 
Cold Starts – This method is best for getting the most flavor and material preservation as you start using as soon as vapor is being produced. Using it in this way will cause the session temperatures to be slightly lower than otherwise because the air passing around the heater will decrease heating speed. You can start your session at any point, we suggest keeping an eye on the button flashes so that you can always begin after a set number of flashes, if desired, providing a very consistent and repeatable experience. 
 
Load material into the heater 
Press the fire button twice to activate session mode 
When your concentrate starts to bubble begin using gently with the carb cap left off 
When the Core 2.0 base vibrates place the carb cap back on and continue your use as you normally would 
For subsequent sessions just use as desired, when the flavor leaves your material, the vapor becomes harsh or stops being produces press the fire button once more to cancel the session 
If you still have material left inside at the end of the session simple hit the fire button twice again and start using immediately, no need to wait for the vibrate as your heater will already be close to adequate temperature. The second session will always run a little hotter than the first if it is started straight after 
Hot Starts –  This way allows the heater to reach full temperature for any given setting; so this method is best for getting the maximum cloud production and effects as quickly as possible. 
 
Press the power button twice to activate session mode 
Load your material onto your dab tool – rice size 
Wait for the Core 2.0 base to vibrate indicating the session temperature has been reached 

While using gently load the dab into the heater, then replace the carb cap and use as your normally would

For subsequent sessions you can carry on as desired. The same applies here with regard to finishing your session. If your material is finished hit the fire button once to cancel the session early, if you still have material left simply hit it twice when the session has ended to start it again! 

As with cold starts, follow up sessions will always run a little hotter. 
Manual – Self explanatory, load a small rice size dab into the heater and hold down the power button. Use as desired. 
 
Manual hold can also be used instead of double pressing to finish a session or heat the heater for easier cleaning. 
 
 
 
Cleaning 
 
Wipe out heater with a Q-tip after each use 
Clean the area around the RDA heater weekly to stop residue building up 
Every month or so wipe out the airway with a Q-tip soaked in ISO – allow to fully dry before use 
Replace bubbler water daily 
To clean bubbler fill with hot water and shake to remove large residues. Soak in ISO to fully clean. Rinse thoroughly with warm water after soaking. 
 
 
Safety Features 
 
Over-charge 
Over-discharge/Low battery 
Over-heat 
Low heater resistance 
Short-circuit 
No atomizer 
 
 
Certifications 
 
CE Certified 
ROHS Certified Materials 
FCC Certification 
FDA Approved Silicone 
UN 38.3 Certified Li-Ion Battery Pack. 
Warning Lights – When your Core 2.0 base flashes three times it’s trying to tell you something… 
 
Blue – Short-circuit warning 
Green – No atomizer warning 
White – Over-heat warning 
Red – Low battery warning 
  
Warranty information 
 
For all warranty claims please contact the store you purchased from. 
The Core 2.0 power base is covered by a one year manufacturer warranty against defects. 
The Core 2.0 carry case is covered by a one year manufacturer warranty against defects. 
The atomizer is covered by a one week manufacturer warranty against defects. 
While atomizers are expected to last much longer than one week, they can be damaged by mishandling and misuse. We understand that not everyone will use the device daily or immediately so offer a one week warranty, from the date of delivery, to report any issue with your atomizer. 

Crossing Core 2.0 | 2.1 Stargazer Side Mouthpiece Bubbler E-Rig Kit

Focus V Carta Sport
The CARTA SPORT introduces a fresh aesthetic with one-button simplicity, perfect for quick, on-the-go sessions. It supports the full line of INTELLI-CORE® atomizers and debuts the all-new CARTA CONNECT, a removable silicone airpath that makes cleaning effortless and opens up a new world of compatibility and customization.

-UP TO 50 DABS PER CHARGE
-CARTA CONNECT
-CONTROL STICK
-INTELLI-CORE® COMPATIBLE
-CARTA GLASS COMPATIBLE
-BLUETOOTH ENABLED
-V REWARDS

WHAT'S INCLUDED:

Water resistant Carrying Case with Shoulder Strap, Silicone Stopper, Loading Tool, Cleaning Swabs, Cleaning Wipes and Owners Manual.

Description
Focus V CARTA Sport
The CARTA Sport is Focus V’s new version of the CARTA Classic. This new electric dab rig has great new accessories. This includes the CARTA Connect and a Control Stick. It also comes with a bigger battery and a Black CARTA Glass Top.

The new, removable CARTA Connect is an air path system that enhances the airflow when you inhale. It fixes reclaim issues to help you get the most from your product. It also makes cleaning your device easier as it is completely removable. We have attached a photo below for reference. 

The air path (CARTA Connect) is removable for simple cleaning. You can put it in the freezer for 10 minutes and use the Loading Tool to scrape off any leftover concentrates.

The Sport also has a new Control Stick. It includes a carb cap for better airflow and taste.

This design heats the product better than before. They make the stick from strong glass and add textured silicone for a better grip. The Control Stick works with all Intelli-Core atomizers and all tethers.

The CARTA Sport has one button, so you don’t need an OLED screen. The battery is also 35% bigger than the CARTA 2 for more dabs per hour. The software now has a longer battery life of up to 50 days per charge. 

Features
Bluetooth enabled
Fully compatible with Intelli-Core atomizers (including MAX)
Compatible with CARTA Glass
Up to 50 dabs per charge
Redeemable V Rewards
Control Stick
CARTA Connect
Comfortable grip
Black glass top
35% larger battery than CARTA 2
Up to 50 dabs per charge
Adjustable presets
Low Power Mode
Includes
1x CARTA Sport Device
1x Intelli-Core Standard Atomizer
1x Owners Manual
1x Black CARTA Glass top
1x Silicone Stopper
Cleaning Wipes
Cleaning Swabs
1x Loading Tool
1x Water Resistant Carrying Case with Strap

Quick Start
Download the Focus V app ‘V Browser’ for custom control.
Click the button 5 times to turn on/off
The device will vibrate, letting you know it is on/off
Double click to start the session
Double click to extend the session by 10 seconds
Single click to end the session
LED will change to orange when heating
Three clicks to cycle through the 5 presets
One click to see which preset you have selected
The LED color will change based on the preset you select 
Four clicks will show you the battery light/level
Click four times and hold the fourth click down to enable Low Power Mode


Blue LED: 480°F
Yellow LED: 495°F
Green LED: 515°F
Purple LED: 535°F
Red LED: 565°F


Always read the user manual for proper use and upkeep

Helpful Resources
How to Use CARTA Sport
Download the V Browser App
Product Registration
Tech Specs
Power Supply    Built-in Battery
Battery Life    50 Dabs per Charge
Heat Time    30 Seconds
Heat Style    Conduction
Temperature    480°F – 565 °F
Use With    Concentrates or Dry Herb
Warranty    1 Year with Focus V
Weight    454g
Connectivity     Bluetooth
Compatible With    CARTA Glass, Intelli-Core Atomizers

Focus V Carta Sport

Crossing Core 3D XL Joystick Kit

THE BRAND NEW CROSSING TECH CORE XL VAPORIZER IS HERE! A newly updated base with 6 heat settings, new XL atomizer, and new Grenade Glass bubbler!

The Core has been updated, to it's core! The new eRig has a brand new power base with 6 heat settings, a new high-flow glass percolator, and is fitted with the 3D XL atomizer! The carb cap has been updated to a joystick style housing.

The Core XL E-rig is the latest portable e-rig from SZ Crossing A.K.A. CrossingTech. It is an all in one dab rig designed for use with a full range of concentrates, from thin oils to solid shatter style material. With a solid build made from high quality materials, a fully heated large capacity cup, vortex airflow and everything you need to get started (except concentrates) it provides the best entry level e-rig experience. After a little practice it rivals much more expensive devices! 


Core XL with Non-Rebuildable Heater
With these you can replace the whole atomizer, the heater is fixed inside. They have been made since some people have no desire to replace heaters in housings so this more convenient solution exists

Joystick Carb Cap

Never stuck. Less maintenance. Always fun. The Core XL Joystick Cap provides precise 360o directional airflow for more consistent heating, giving you bigger clouds and better flavor. Made of shatterproof stainless steel and silicone, the Joystick’s design is easy to clean and prevents reclaim from stopping your flow. And it’s fidget friendly.


Features

Core XL runs XL 3D Ceramic heaters only, no wire based coils
Atomizers contain only Metal and Ceramic, silicone and PEEK has been replaced with an all ceramic design
Six Heat settings
Increased total session time (80 second full run time)
Vortex airflow - included updated spinner carb cap
360 Degree Joystick Carb Cap
Improved button function
Upgraded Carb Cap housing
One button functionality for ease of use
Fully heated high polish ceramic vaping surface - elements inside base and walls of heater
Rebuildable or non-rebuildable atomizer options 
Borosilicate Glass Bubbler Grenade Bubbler - an upgrade over previous Core bubblers 
Updated Stainless Steel Carb Cap Tube and heat dissipator
Isolated Anodized Aluminium and Glass Vapor Pathway
Low maintenance 
Approx. 1 hour 45 minute charging time
3150mah Li-Ion Battery Pack
Approx. 21 full sessions - mixed power settings 
 

What's Included

Core XL E-rig Base with six heat settings
Core Grenade bubbler with better function and angled mouthpiece
Joystick Carb Cap and Housing
Silicone Base Cover/Sleeve (black)
Core XL 3D Ceramic Atomizer
SS316 Dab Tool
2 x Spare Carb Cap Tube O-rings
1 x USB-C Charging Cable
Cotton buds/Q-tips
Alcohol wipes 
Carry Case
 

Button Function

Two clicks - Activate session mode - One click to cancel
One Clicks - Change heat setting 
Four Click - Display power level - Red/Low - White/Medium - Green/Full
Five Clicks - Lock or unlock device
 

Sessions times and temperatures

The total session time for the Core XL has been upgraded to 80 seconds, this includes the pre-heat time. It now has 6 heat settings, click once to cycle through these. 

Purple / Lowest - 320f after preheat 
Yellow / Second lowest - 330f after preheat 
Blue / Middle - 350f after preheat
Green / Middle high - 395f after preheat
White / Second highest - 450f after preheat
Red / Highest - 500f after preheat
 

Setup

Always hold your e-rig upright! If you angle it during use concentrate will spill out the bucket! Now that's out the way...
Charge your base using the provided wall plug and cable. 
Fill the bubbler from the top, when it is removed from the base. Ensure any excess liquid has been wiped away and that no water has flooded into the bottom compartment. If this happens turn the bubbler upside down and blow into the air hole at the bottom to clear this section. Then re-fill from the top. 
Do not fill the bubbler past 1/4 fill height or you risk flooding the base and damaging the unit. Just above the airflow slits inside is fine.
When replacing the bubbler, place it on the base at an angle, ensuring that the hole in the bubbler base aligns with the vapor pathway, then gently and firmly push it straight down into place. 
For Rebuldable Atomizer check the small screws in the atomizer base which hold the heater legs are done up fully. These need to be tightened so they are firm, but not so much that they cut the wire legs off the heater. 
Select your desired heat setting (start low if you're not sure).
 

Vaping methods

Cold Starts - This method is best for getting the most flavour and material preservation as you start inhaling as soon as vapour is being produced. Vaping in this way will cause the session temperatures to be slightly lower than otherwise because the air passing around the heater will decrease heating speed.  You can start your inhale at any point, we suggest keeping an eye on the button flashes so that you can always begin inhaling after a set number of flashes, if desired, providing a very consistent and repeatable experience. 

Load a rice grain size dab (basmati not long grain) into the heater
Press the fire button twice to activate session mode
When your concentrate starts to bubble begin inhaling gently with the carb cap left off
When the Core 2.0 base vibrates place the carb cap back on and continue your inhale as you normally would
For subsequent inhalations just inhale as desired, when the flavour leaves your material, the vapor becomes harsh or stops being produces press the fire button once more to cancel the session
If you still have material left inside at the end of the session simple hit the fire button twice again and start vaping immediately, no need to wait for the vibrate as your heater will already be close to vaping temperature. The second session will always run a little hotter than the first if it is started straight after
It's been advised by the manufacturer to avoid doing hot starts where the dab is loaded into a pre-heated heater as this can crack the ceramic due to the temperature difference
Manual - Self explanatory, load a small rice size dab into the heater and hold down the power button. Inhale as desired. 

Manual hold can also be used instead of double pressing to finish a session or heat the heater for easier cleaning. 

 

Cleaning

Wipe out heater with a q-tip after each use
Clean the area around the atomizer weekly to stop residue building up
Every month or so wipe out the airway with a q-tip soaked in ISO - allow to fully dry before use
Replace bubbler water daily
To clean bubbler fill with hot water and shake to remove large residues. Soak in ISO to fully clean. Rinse thoroughly with warm water after soaking.  
The Core Atomizer can also be removed and screwed into a heat sink on our Pico Plus with auto-fire or an Arctic Fox or DNA-C box mod (with auto-fire), then run at 36W upside down for 1-2 mins to perform a burn off cycle to clean the heater back to new. This is optional. You can also use the CUB instead of a heat sink with this setup, the CUB can also be used with the atomizers as a standalone portable when paired with a box mod such as the Pico Plus. 
 

Safety Features 

Over-charge 
Over-discharge/Low battery
Over-heat 
Low heater resistance
Short-circuit 
No atomizer 
 

Certifications

CE Certified
ROHS Certified Materials
FCC Certification
FDA Approved Silicone
UN 38.3 Certified Li-Ion Battery Pack. 
 

Warning Lights - When your Core 2.0 base flashes three times it's trying to tell you something...

Blue - Short-circuit warning
Green - No atomizer warning
White - Over-heat warning
Red - Low battery warning
 

Warranty information

For all warranty claims please contact the store you purchased from.
The Core XL power base is covered by a one year manufacturer warranty against defects.
The atomizer is covered by a one week manufacturer warranty against defects, this can be damaged by aggressive cleaning or accidental damage from tools.
While atomizers are expected to last much longer than one week, they can be damaged by mishandling and misuse. We understand that not everyone will use the device daily or immediately so offer a one week warranty, from the date of delivery, to report any issue with your atomizer.

Note: older coils and RDAs from the Core and Core2 will work on the new Core XL.

Crossing Core 3D XL Joystick Kit

Crossing Core 2.0 | 2.1 Flat Top Matrix Percolator Bubbler E-Rig Kit
Model Choice: 2.0 or 2.1

The one you've been waiting for... Core 2.0 e-rig with a black silicone sleeve and carb tether, 4-port spinner carb cap and V5 Heater!! 
When heater housing design and art combines! Meet the new rebuildable ceramic coil for the Core 2.0 E-Rig. The RDA V5 Ceramic Heater works on the original Core also. The original Core coil atomizers work on the Core 2.0 too! 
  
There are a some key differences between the Core and Core 2.0 e-rigs which are as follows: 
 
Core 2.0 runs V5 heaters, no wire based coils 
Atomizers contain only Metal and Ceramic, silicone and PEEK has been replaced with an all ceramic design 
Four heat settings are now all for the V5 heaters 
Fully rebuildable atomizers – no need to replace the whole housing, just the heater 
Decreased pre-heat time 
Increased session time 
Increased total run time (80 second full run time) 
Vortex airflow – included spinner carb cap 
“Unbreakable” aluminum carb cap replaces glass bubble carb 
Improved button function 
Upgraded Stainless Steel Carb Cap Tube 
 
 
Features 
 
One button functionality for ease of use 
Fully heated high polish ceramic vaping surface – elements inside base and walls of heater 
Rebuildable atomizer 
Vortex Airflow – Aluminum spinner carb cap with carb cap tether 
Borosilicate Glass Bubbler 
Stainless Steel Carb Cap Tube 
Four carefully tuned heat settings 
Isolated Aluminum and Glass Vapor Pathway 
Low maintenance 
Approx. 1 hour 45 minute charging time 
3150mah Li-Ion Battery Pack. 
 
 
What’s Included 
 
Core 2.0|2.1 E-rig Base 
Core Flat Top Matrix Percolator Bubbler 
Factory Travel Glass Bubbler
Aluminum Spinner Carb Cap (based on our design)
Carb Cap Tether (black)
Silicone Base Cover/Sleeve (black) 
Atomizer with V5 heater installed 
Spare V5 Heater 
SS316 Dab Tool (based on our design) 
4 x Spare Atomizer Screws 
Screwdriver 
2 x Spare Carb Cap Tube O-rings 
1 x Wall Plug 
1 x USB-C Charging Cable 
Cotton buds/Q-tips 
Alcohol wipes 
Carrying Case 
 
Button Functions 
 
Hold – Manual fire up to 60 seconds 
Two clicks – Activate session mode – One click to cancel 
Three Clicks – Change heat setting 
Four Click – Display power level – Red/Low – White/Medium – Green/Full 
Five Clicks – Lock or unlock Core 2.0 Base 
 
 
Sessions times and temperatures 
 
The total session time for the Core 2.0 has been upgraded to 80 seconds, this includes the pre-heat time. 
 
Blue – 12.5 second pre-heat – Approx. 400° 
Green – 13 second pre-heat – Approx. 425° 
White – 17.5 second pre-heat – Approx. 465° 
Red – 22.5 second pre-heat – Approx. 500° 
 
 
Setup 
 
Charge your base using the provided wall plug and cable. 
Fill the bubbler from the top, when it is removed from the base. Ensure any excess liquid has been wiped away and that no water has flooded into the bottom compartment. If this happens turn the bubbler upside down and blow into the air hole at the bottom to clear this section. Then re-fill from the top. 

Place bubbler onto Core 2.0 Base at an angle, ensuring that the hole in the bubbler base aligns with the vapor pathway in the Core 2.0 base, then gently and firmly push it straight down into place. 

Check small screws in the atomizer base which hold the heater legs are done up fully. These need to be tightened so they are firm, but not so much that they cut the wire legs off the heater. When this is done screw the atomizer into the Core 2.0 base. 

Place the carb cap tube on the base so that the wider angled side sits at the top, leaving the carp cab on the tether so that you can load concentrate onto the heater. 
Select your desired heat setting (start low if you’re not sure). 

Now that’s all done we get onto the vaping methods as there are different ways the Core 2.0 can be used! 
 
 
Methods of Use 
 
Cold Starts – This method is best for getting the most flavor and material preservation as you start using as soon as vapor is being produced. Using it in this way will cause the session temperatures to be slightly lower than otherwise because the air passing around the heater will decrease heating speed. You can start your session at any point, we suggest keeping an eye on the button flashes so that you can always begin after a set number of flashes, if desired, providing a very consistent and repeatable experience. 
 
Load material into the heater 
Press the fire button twice to activate session mode 
When your concentrate starts to bubble begin using gently with the carb cap left off 
When the Core 2.0 base vibrates place the carb cap back on and continue your use as you normally would 
For subsequent sessions just use as desired, when the flavor leaves your material, the vapor becomes harsh or stops being produces press the fire button once more to cancel the session 
If you still have material left inside at the end of the session simple hit the fire button twice again and start using immediately, no need to wait for the vibrate as your heater will already be close to adequate temperature. The second session will always run a little hotter than the first if it is started straight after 
Hot Starts –  This way allows the heater to reach full temperature for any given setting; so this method is best for getting the maximum cloud production and effects as quickly as possible. 
 
Press the power button twice to activate session mode 
Load your material onto your dab tool – rice size 
Wait for the Core 2.0 base to vibrate indicating the session temperature has been reached 

While using gently load the dab into the heater, then replace the carb cap and use as your normally would

For subsequent sessions you can carry on as desired. The same applies here with regard to finishing your session. If your material is finished hit the fire button once to cancel the session early, if you still have material left simply hit it twice when the session has ended to start it again! 

As with cold starts, follow up sessions will always run a little hotter. 
Manual – Self explanatory, load a small rice size dab into the heater and hold down the power button. Use as desired. 
 
Manual hold can also be used instead of double pressing to finish a session or heat the heater for easier cleaning. 
 
 
 
Cleaning 
 
Wipe out heater with a Q-tip after each use 
Clean the area around the RDA heater weekly to stop residue building up 
Every month or so wipe out the airway with a Q-tip soaked in ISO – allow to fully dry before use 
Replace bubbler water daily 
To clean bubbler fill with hot water and shake to remove large residues. Soak in ISO to fully clean. Rinse thoroughly with warm water after soaking. 
 
 
Safety Features 
 
Over-charge 
Over-discharge/Low battery 
Over-heat 
Low heater resistance 
Short-circuit 
No atomizer 
 
 
Certifications 
 
CE Certified 
ROHS Certified Materials 
FCC Certification 
FDA Approved Silicone 
UN 38.3 Certified Li-Ion Battery Pack. 
Warning Lights – When your Core 2.0 base flashes three times it’s trying to tell you something… 
 
Blue – Short-circuit warning 
Green – No atomizer warning 
White – Over-heat warning 
Red – Low battery warning 
  
Warranty information 
 
For all warranty claims please contact the store you purchased from. 
The Core 2.0 power base is covered by a one year manufacturer warranty against defects. 
The Core 2.0 carry case is covered by a one year manufacturer warranty against defects. 
The atomizer is covered by a one week manufacturer warranty against defects. 
While atomizers are expected to last much longer than one week, they can be damaged by mishandling and misuse. We understand that not everyone will use the device daily or immediately so offer a one week warranty, from the date of delivery, to report any issue with your atomizer. 

Crossing Core 2.0 | 2.1 Flat Top Matrix Percolator Bubbler E-Rig Kit

Crossing Core 2.0 | 2.1 Curved Hanger Glass Bubbler E-Rig Kit
Features a curved glass neck for a relaxed session

Model Choice: 2.0 or 2.1

The one you've been waiting for... Core 2.0 e-rig with a black silicone sleeve and carb tether, 4-port spinner carb cap and V5 Heater!!
When heater housing design and art combines! Meet the new rebuildable ceramic coil for the Core 2.0 E-Rig. The RDA V5 Ceramic Heater works on the original Core also. The original Core coil atomizers work on the Core 2.0 too!
 
There are a some key differences between the Core and Core 2.0 e-rigs which are as follows:

Core 2.0 runs V5 heaters, no wire based coils
Atomizers contain only Metal and Ceramic, silicone and PEEK has been replaced with an all ceramic design
Four heat settings are now all for the V5 heaters
Fully rebuildable atomizers – no need to replace the whole housing, just the heater
Decreased pre-heat time
Increased session time
Increased total run time (80 second full run time)
Vortex airflow – included spinner carb cap
“Unbreakable” aluminum carb cap replaces glass bubble carb
Improved button function
Upgraded Stainless Steel Carb Cap Tube


Features

One button functionality for ease of use
Fully heated high polish ceramic vaping surface – elements inside base and walls of heater
Rebuildable atomizer
Vortex Airflow – Aluminum spinner carb cap with carb cap tether
Borosilicate Glass Bubbler
Stainless Steel Carb Cap Tube
Four carefully tuned heat settings
Isolated Aluminum and Glass Vapor Pathway
Low maintenance
Approx. 1 hour 45 minute charging time
3150mah Li-Ion Battery Pack.


What’s Included

Core 2.0|2.1 E-rig Base
Curved Hanger Glass Bubbler
Factory Travel Glass Bubbler
Aluminum Spinner Carb Cap (based on our design)
Carb Cap Tether (black)
Silicone Base Cover/Sleeve (black)
Atomizer with V5 heater installed
Spare V5 Heater
SS316 Dab Tool (based on our design)
4 x Spare Atomizer Screws
Screwdriver
2 x Spare Carb Cap Tube O-rings
1 x Wall Plug
1 x USB-C Charging Cable
Cotton buds/Q-tips
Alcohol wipes
Carrying Case


Button Functions

Hold – Manual fire up to 60 seconds
Two clicks – Activate session mode – One click to cancel
Three Clicks – Change heat setting
Four Click – Display power level – Red/Low – White/Medium – Green/Full
Five Clicks – Lock or unlock Core 2.0 Base


Sessions times and temperatures

The total session time for the Core 2.0 has been upgraded to 80 seconds, this includes the pre-heat time.

Blue – 12.5 second pre-heat – Approx. 400°
Green – 13 second pre-heat – Approx. 425°
White – 17.5 second pre-heat – Approx. 465°
Red – 22.5 second pre-heat – Approx. 500°


Setup

Charge your base using the provided wall plug and cable.
Fill the bubbler from the top, when it is removed from the base. Ensure any excess liquid has been wiped away and that no water has flooded into the bottom compartment. If this happens turn the bubbler upside down and blow into the air hole at the bottom to clear this section. Then re-fill from the top.

Place bubbler onto Core 2.0 Base at an angle, ensuring that the hole in the bubbler base aligns with the vapor pathway in the Core 2.0 base, then gently and firmly push it straight down into place.

Check small screws in the atomizer base which hold the heater legs are done up fully. These need to be tightened so they are firm, but not so much that they cut the wire legs off the heater. When this is done screw the atomizer into the Core 2.0 base.

Place the carb cap tube on the base so that the wider angled side sits at the top, leaving the carp cab on the tether so that you can load concentrate onto the heater.
Select your desired heat setting (start low if you’re not sure).

Now that’s all done we get onto the vaping methods as there are different ways the Core 2.0 can be used!


Methods of Use

Cold Starts – This method is best for getting the most flavor and material preservation as you start using as soon as vapor is being produced. Using it in this way will cause the session temperatures to be slightly lower than otherwise because the air passing around the heater will decrease heating speed. You can start your session at any point, we suggest keeping an eye on the button flashes so that you can always begin after a set number of flashes, if desired, providing a very consistent and repeatable experience.

Load material into the heater
Press the fire button twice to activate session mode
When your concentrate starts to bubble begin using gently with the carb cap left off
When the Core 2.0 base vibrates place the carb cap back on and continue your use as you normally would
For subsequent sessions just use as desired, when the flavor leaves your material, the vapor becomes harsh or stops being produces press the fire button once more to cancel the session
If you still have material left inside at the end of the session simple hit the fire button twice again and start using immediately, no need to wait for the vibrate as your heater will already be close to adequate temperature. The second session will always run a little hotter than the first if it is started straight after
Hot Starts –  This way allows the heater to reach full temperature for any given setting; so this method is best for getting the maximum cloud production and effects as quickly as possible.

Press the power button twice to activate session mode
Load your material onto your dab tool – rice size
Wait for the Core 2.0 base to vibrate indicating the session temperature has been reached

While using gently load the dab into the heater, then replace the carb cap and use as your normally would

For subsequent sessions you can carry on as desired. The same applies here with regard to finishing your session. If your material is finished hit the fire button once to cancel the session early, if you still have material left simply hit it twice when the session has ended to start it again!

As with cold starts, follow up sessions will always run a little hotter.
Manual – Self explanatory, load a small rice size dab into the heater and hold down the power button. Use as desired.

Manual hold can also be used instead of double pressing to finish a session or heat the heater for easier cleaning.



Cleaning

Wipe out heater with a Q-tip after each use
Clean the area around the RDA heater weekly to stop residue building up
Every month or so wipe out the airway with a Q-tip soaked in ISO – allow to fully dry before use
Replace bubbler water daily
To clean bubbler fill with hot water and shake to remove large residues. Soak in ISO to fully clean. Rinse thoroughly with warm water after soaking.


Safety Features

Over-charge
Over-discharge/Low battery
Over-heat
Low heater resistance
Short-circuit
No atomizer


Certifications

CE Certified
ROHS Certified Materials
FCC Certification
FDA Approved Silicone
UN 38.3 Certified Li-Ion Battery Pack.
Warning Lights – When your Core 2.0 base flashes three times it’s trying to tell you something…

Blue – Short-circuit warning
Green – No atomizer warning
White – Over-heat warning
Red – Low battery warning
 
Warranty information

For all warranty claims please contact the store you purchased from.
The Core 2.0 power base is covered by a one year manufacturer warranty against defects.
The Core 2.0 carry case is covered by a one year manufacturer warranty against defects.
The atomizer is covered by a one week manufacturer warranty against defects.
While atomizers are expected to last much longer than one week, they can be damaged by mishandling and misuse. We understand that not everyone will use the device daily or immediately so offer a one week warranty, from the date of delivery, to report any issue with your atomizer.



Crossing Core 2.0 | 2.1 Curved Hanger Glass Bubbler E-Rig Kit

Crossing Core 2.0 | 2.1 Grenade Glass Bubbler E-Rig Kit
Model Choice: 2.0 or 2.1

The one you've been waiting for... Core 2.0 e-rig with a black silicone sleeve and carb tether, 4-port spinner carb cap and V5 Heater!! 
When heater housing design and art combines! Meet the new rebuildable ceramic coil for the Core 2.0 E-Rig. The RDA V5 Ceramic Heater works on the original Core also. The original Core coil atomizers work on the Core 2.0 too! 
  
There are a some key differences between the Core and Core 2.0 e-rigs which are as follows: 
 
Core 2.0 runs V5 heaters, no wire based coils 
Atomizers contain only Metal and Ceramic, silicone and PEEK has been replaced with an all ceramic design 
Four heat settings are now all for the V5 heaters 
Fully rebuildable atomizers – no need to replace the whole housing, just the heater 
Decreased pre-heat time 
Increased session time 
Increased total run time (80 second full run time) 
Vortex airflow – included spinner carb cap 
“Unbreakable” aluminum carb cap replaces glass bubble carb 
Improved button function 
Upgraded Stainless Steel Carb Cap Tube 
 
 
Features 
 
One button functionality for ease of use 
Fully heated high polish ceramic vaping surface – elements inside base and walls of heater 
Rebuildable atomizer 
Vortex Airflow – Aluminum spinner carb cap with carb cap tether 
Borosilicate Glass Bubbler 
Stainless Steel Carb Cap Tube 
Four carefully tuned heat settings 
Isolated Aluminum and Glass Vapor Pathway 
Low maintenance 
Approx. 1 hour 45 minute charging time 
3150mah Li-Ion Battery Pack. 
 
 
What’s Included 
 
Core 2.0|2.1 E-rig Base 
Core Grenade Glass Bubbler 
Factory Travel Glass Bubbler
Aluminum Spinner Carb Cap (based on our design) 
Carb Cap Tether (black) 
Silicone Base Cover/Sleeve (black) 
Atomizer with V5 heater installed 
Spare V5 Heater 
SS316 Dab Tool (based on our design) 
4 x Spare Atomizer Screws 
Screwdriver 
2 x Spare Carb Cap Tube O-rings 
1 x Wall Plug
1 x USB-C Charging Cable 
Cotton buds/Q-tips 
Alcohol wipes 
Carrying Case 
 
 
Button Functions 
 
Hold – Manual fire up to 60 seconds 
Two clicks – Activate session mode – One click to cancel 
Three Clicks – Change heat setting 
Four Click – Display power level – Red/Low – White/Medium – Green/Full 
Five Clicks – Lock or unlock Core 2.0 Base 
 
 
Sessions times and temperatures 
 
The total session time for the Core 2.0 has been upgraded to 80 seconds, this includes the pre-heat time. 
 
Blue – 12.5 second pre-heat – Approx. 400° 
Green – 13 second pre-heat – Approx. 425° 
White – 17.5 second pre-heat – Approx. 465° 
Red – 22.5 second pre-heat – Approx. 500° 
 
 
Setup 
 
Charge your base using the provided wall plug and cable. 
Fill the bubbler from the top, when it is removed from the base. Ensure any excess liquid has been wiped away and that no water has flooded into the bottom compartment. If this happens turn the bubbler upside down and blow into the air hole at the bottom to clear this section. Then re-fill from the top. 

Place bubbler onto Core 2.0 Base at an angle, ensuring that the hole in the bubbler base aligns with the vapor pathway in the Core 2.0 base, then gently and firmly push it straight down into place. 

Check small screws in the atomizer base which hold the heater legs are done up fully. These need to be tightened so they are firm, but not so much that they cut the wire legs off the heater. When this is done screw the atomizer into the Core 2.0 base. 

Place the carb cap tube on the base so that the wider angled side sits at the top, leaving the carp cab on the tether so that you can load concentrate onto the heater. 
Select your desired heat setting (start low if you’re not sure). 

Now that’s all done we get onto the vaping methods as there are different ways the Core 2.0 can be used! 
 
 
Methods of Use 
 
Cold Starts – This method is best for getting the most flavor and material preservation as you start using as soon as vapor is being produced. Using it in this way will cause the session temperatures to be slightly lower than otherwise because the air passing around the heater will decrease heating speed. You can start your session at any point, we suggest keeping an eye on the button flashes so that you can always begin after a set number of flashes, if desired, providing a very consistent and repeatable experience. 
 
Load material into the heater 
Press the fire button twice to activate session mode 
When your concentrate starts to bubble begin using gently with the carb cap left off 
When the Core 2.0 base vibrates place the carb cap back on and continue your use as you normally would 
For subsequent sessions just use as desired, when the flavor leaves your material, the vapor becomes harsh or stops being produces press the fire button once more to cancel the session 
If you still have material left inside at the end of the session simple hit the fire button twice again and start using immediately, no need to wait for the vibrate as your heater will already be close to adequate temperature. The second session will always run a little hotter than the first if it is started straight after 
Hot Starts –  This way allows the heater to reach full temperature for any given setting; so this method is best for getting the maximum cloud production and effects as quickly as possible. 
 
Press the power button twice to activate session mode 
Load your material onto your dab tool – rice size 
Wait for the Core 2.0 base to vibrate indicating the session temperature has been reached 

While using gently load the dab into the heater, then replace the carb cap and use as your normally would

For subsequent sessions you can carry on as desired. The same applies here with regard to finishing your session. If your material is finished hit the fire button once to cancel the session early, if you still have material left simply hit it twice when the session has ended to start it again! 

As with cold starts, follow up sessions will always run a little hotter. 
Manual – Self explanatory, load a small rice size dab into the heater and hold down the power button. Use as desired. 
 
Manual hold can also be used instead of double pressing to finish a session or heat the heater for easier cleaning. 
 
 
 
Cleaning 
 
Wipe out heater with a Q-tip after each use 
Clean the area around the RDA heater weekly to stop residue building up 
Every month or so wipe out the airway with a Q-tip soaked in ISO – allow to fully dry before use 
Replace bubbler water daily 
To clean bubbler fill with hot water and shake to remove large residues. Soak in ISO to fully clean. Rinse thoroughly with warm water after soaking. 
 
 
Safety Features 
 
Over-charge 
Over-discharge/Low battery 
Over-heat 
Low heater resistance 
Short-circuit 
No atomizer 
 
 
Certifications 
 
CE Certified 
ROHS Certified Materials 
FCC Certification 
FDA Approved Silicone 
UN 38.3 Certified Li-Ion Battery Pack. 
Warning Lights – When your Core 2.0 base flashes three times it’s trying to tell you something… 
 
Blue – Short-circuit warning 
Green – No atomizer warning 
White – Over-heat warning 
Red – Low battery warning 
  
Warranty information 
 
For all warranty claims please contact the store you purchased from. 
The Core 2.0 power base is covered by a one year manufacturer warranty against defects. 
The Core 2.0 carry case is covered by a one year manufacturer warranty against defects. 
The atomizer is covered by a one week manufacturer warranty against defects. 
While atomizers are expected to last much longer than one week, they can be damaged by mishandling and misuse. We understand that not everyone will use the device daily or immediately so offer a one week warranty, from the date of delivery, to report any issue with your atomizer. 

Crossing Core 2.0 | 2.1 Grenade Glass Bubbler E-Rig Kit

Crossing Core 2.0 | 2.1 Mini Incycler Recycling Bubbler E-Rig Kit
Model Choice: 2.0 or 2.1
The one you've been waiting for... Core 2.0 e-rig with a black silicone sleeve and carb tether, 4-port spinner carb cap and V5 Heater!!
When heater housing design and art combines! Meet the new rebuildable ceramic coil for the Core 2.0 E-Rig. The RDA V5 Ceramic Heater works on the original Core also. The original Core coil atomizers work on the Core 2.0 too!
 
There are a some key differences between the Core and Core 2.0 e-rigs which are as follows:

Core 2.0 runs V5 heaters, no wire based coils
Atomizers contain only Metal and Ceramic, silicone and PEEK has been replaced with an all ceramic design
Four heat settings are now all for the V5 heaters
Fully rebuildable atomizers – no need to replace the whole housing, just the heater
Decreased pre-heat time
Increased session time
Increased total run time (80 second full run time)
Vortex airflow – included spinner carb cap
“Unbreakable” aluminum carb cap replaces glass bubble carb
Improved button function
Upgraded Stainless Steel Carb Cap Tube


Features

One button functionality for ease of use
Fully heated high polish ceramic vaping surface – elements inside base and walls of heater
Rebuildable atomizer
Vortex Airflow – Aluminum spinner carb cap with carb cap tether
Borosilicate Glass Bubbler
Stainless Steel Carb Cap Tube
Four carefully tuned heat settings
Isolated Aluminum and Glass Vapor Pathway
Low maintenance
Approx. 1 hour 45 minute charging time
3150mah Li-Ion Battery Pack.


What’s Included

Core 2.0|2.1 E-Rig Base
Core Mini Incycler Recycling Bubbler
Aluminum Spinner Carb Cap (based on our design)
Carb Cap Tether (black)
Silicone Base Cover/Sleeve (black)
Atomizer with V5 heater installed
Spare V5 Heater
SS316 Dab Tool (based on our design)
4 x Spare Atomizer Screws
Screwdriver
2 x Spare Carb Cap Tube O-rings
1 x Wall Plug
1 x USB-C Charging Cable
Cotton buds/Q-tips
Alcohol wipes
Special Carrying Case to fit this Glass

Button Functions

Hold – Manual fire up to 60 seconds
Two clicks – Activate session mode – One click to cancel
Three Clicks – Change heat setting
Four Click – Display power level – Red/Low – White/Medium – Green/Full
Five Clicks – Lock or unlock Core 2.0 Base


Sessions times and temperatures

The total session time for the Core 2.0 has been upgraded to 80 seconds, this includes the pre-heat time.

Blue – 12.5 second pre-heat – Approx. 400°
Green – 13 second pre-heat – Approx. 425°
White – 17.5 second pre-heat – Approx. 465°
Red – 22.5 second pre-heat – Approx. 500°


Setup

Charge your base using the provided wall plug and cable.
Fill the bubbler from the top, when it is removed from the base. Ensure any excess liquid has been wiped away and that no water has flooded into the bottom compartment. If this happens turn the bubbler upside down and blow into the air hole at the bottom to clear this section. Then re-fill from the top.

Place bubbler onto Core 2.0 Base at an angle, ensuring that the hole in the bubbler base aligns with the vapor pathway in the Core 2.0 base, then gently and firmly push it straight down into place.

Check small screws in the atomizer base which hold the heater legs are done up fully. These need to be tightened so they are firm, but not so much that they cut the wire legs off the heater. When this is done screw the atomizer into the Core 2.0 base.

Place the carb cap tube on the base so that the wider angled side sits at the top, leaving the carp cab on the tether so that you can load concentrate onto the heater.
Select your desired heat setting (start low if you’re not sure).

Now that’s all done we get onto the vaping methods as there are different ways the Core 2.0 can be used!


Methods of Use

Cold Starts – This method is best for getting the most flavor and material preservation as you start using as soon as vapor is being produced. Using it in this way will cause the session temperatures to be slightly lower than otherwise because the air passing around the heater will decrease heating speed. You can start your session at any point, we suggest keeping an eye on the button flashes so that you can always begin after a set number of flashes, if desired, providing a very consistent and repeatable experience.

Load material into the heater
Press the fire button twice to activate session mode
When your concentrate starts to bubble begin using gently with the carb cap left off
When the Core 2.0 base vibrates place the carb cap back on and continue your use as you normally would
For subsequent sessions just use as desired, when the flavor leaves your material, the vapor becomes harsh or stops being produces press the fire button once more to cancel the session
If you still have material left inside at the end of the session simple hit the fire button twice again and start using immediately, no need to wait for the vibrate as your heater will already be close to adequate temperature. The second session will always run a little hotter than the first if it is started straight after
Hot Starts –  This way allows the heater to reach full temperature for any given setting; so this method is best for getting the maximum cloud production and effects as quickly as possible.

Press the power button twice to activate session mode
Load your material onto your dab tool – rice size
Wait for the Core 2.0 base to vibrate indicating the session temperature has been reached

While using gently load the dab into the heater, then replace the carb cap and use as your normally would

For subsequent sessions you can carry on as desired. The same applies here with regard to finishing your session. If your material is finished hit the fire button once to cancel the session early, if you still have material left simply hit it twice when the session has ended to start it again!

As with cold starts, follow up sessions will always run a little hotter.
Manual – Self explanatory, load a small rice size dab into the heater and hold down the power button. Use as desired.

Manual hold can also be used instead of double pressing to finish a session or heat the heater for easier cleaning.



Cleaning

Wipe out heater with a Q-tip after each use
Clean the area around the RDA heater weekly to stop residue building up
Every month or so wipe out the airway with a Q-tip soaked in ISO – allow to fully dry before use
Replace bubbler water daily
To clean bubbler fill with hot water and shake to remove large residues. Soak in ISO to fully clean. Rinse thoroughly with warm water after soaking.


Safety Features

Over-charge
Over-discharge/Low battery
Over-heat
Low heater resistance
Short-circuit
No atomizer


Certifications

CE Certified
ROHS Certified Materials
FCC Certification
FDA Approved Silicone
UN 38.3 Certified Li-Ion Battery Pack.
Warning Lights – When your Core 2.0 base flashes three times it’s trying to tell you something…

Blue – Short-circuit warning
Green – No atomizer warning
White – Over-heat warning
Red – Low battery warning
 
Warranty information

For all warranty claims please contact the store you purchased from.
The Core 2.0 power base is covered by a one year manufacturer warranty against defects.
The Core 2.0 carry case is covered by a one year manufacturer warranty against defects.
The atomizer is covered by a one week manufacturer warranty against defects.
While atomizers are expected to last much longer than one week, they can be damaged by mishandling and misuse. We understand that not everyone will use the device daily or immediately so offer a one week warranty, from the date of delivery, to report any issue with your atomizer.

Crossing Core 2.0 | 2.1 Mini Incycler Recycling Bubbler E-Rig Kit

Paramour 4 Smart E-Rig Kit
The Paramour 4 changed everything. Right size to hold in one hand, Craft your perfect dabbing experience with precision using Paramour 4, a high-performing 3D Ceramic Heating Chamber featuring the Joystick Cap and laser cut perc slots, make Full Heating Full Flavor. Last you about 30 sessions before needing a recharge. Featuring premium water filtration for smoother hits, unique user heat settings and a single-button interface, The Paramour 4 makes enjoying hash easy.
 

Easy One-Button Control:
Built-in buttons and east user-friendly LED display. Enjoy a hassle-free experience with direct temperature control and automatic heating.
 

Precise Temperature Adjustment:
Instead of fixed temperature increments, customize your experience with precision, paired with the 3D ceramic chamber, fine-tuning the temperature to achieve the perfect dab
 

Powerful Hits:
Powerful hits that deliver heavy clouds for an intense dab session

What's Included
Paramour 4 Device, Loading Tool, Micro USB Cable

Paramour Protection & Warranty
The Paramour 4 is covered for 180 days under the Paramour warranty

Paramour 4 Smart E-Rig Kit

Crossing Core 2.0 | 2.1 Recycling Bubbler E-Rig Kit
Model Choice: 2.0 or 2.1

The one you've been waiting for... Core 2.0 e-rig with a black silicone sleeve and carb tether, 4-port spinner carb cap and V5 Heater!! 
When heater housing design and art combines! Meet the new rebuildable ceramic coil for the Core 2.0 E-Rig. The RDA V5 Ceramic Heater works on the original Core also. The original Core coil atomizers work on the Core 2.0 too! 
  
There are a some key differences between the Core and Core 2.0 e-rigs which are as follows: 
 
Core 2.0 runs V5 heaters, no wire based coils 
Atomizers contain only Metal and Ceramic, silicone and PEEK has been replaced with an all ceramic design 
Four heat settings are now all for the V5 heaters 
Fully rebuildable atomizers – no need to replace the whole housing, just the heater 
Decreased pre-heat time 
Increased session time 
Increased total run time (80 second full run time) 
Vortex airflow – included spinner carb cap 
“Unbreakable” aluminum carb cap replaces glass bubble carb 
Improved button function 
Upgraded Stainless Steel Carb Cap Tube 
 
 
Features 
 
One button functionality for ease of use 
Fully heated high polish ceramic vaping surface – elements inside base and walls of heater 
Rebuildable atomizer 
Vortex Airflow – Aluminum spinner carb cap with carb cap tether 
Borosilicate Glass Bubbler 
Stainless Steel Carb Cap Tube 
Four carefully tuned heat settings 
Isolated Aluminum and Glass Vapor Pathway 
Low maintenance 
Approx. 1 hour 45 minute charging time 
3150mah Li-Ion Battery Pack. 
 
 
What’s Included 
 
Core 2.0|2.1 E-rig Base 
Core Recycling Perc Bubbler 
Factory Travel Glass Bubbler
Aluminum Spinner Carb Cap (based on our design) 
Carb Cap Tether (black) 
Silicone Base Cover/Sleeve (black) 
Atomizer with V5 heater installed 
Spare V5 Heater 
SS316 Dab Tool (based on our design) 
4 x Spare Atomizer Screws 
Screwdriver 
2 x Spare Carb Cap Tube O-rings 
1 x Wall Plug 
1 x USB-C Charging Cable 
Cotton buds/Q-tips 
Alcohol wipes 
Carrying Case 
 
Button Functions 
 
Hold – Manual fire up to 60 seconds 
Two clicks – Activate session mode – One click to cancel 
Three Clicks – Change heat setting 
Four Click – Display power level – Red/Low – White/Medium – Green/Full 
Five Clicks – Lock or unlock Core 2.0 Base 
 
 
Sessions times and temperatures 
 
The total session time for the Core 2.0 has been upgraded to 80 seconds, this includes the pre-heat time. 
 
Blue – 12.5 second pre-heat – Approx. 400° 
Green – 13 second pre-heat – Approx. 425° 
White – 17.5 second pre-heat – Approx. 465° 
Red – 22.5 second pre-heat – Approx. 500° 
 
 
Setup 
 
Charge your base using the provided wall plug and cable. 
Fill the bubbler from the top, when it is removed from the base. Ensure any excess liquid has been wiped away and that no water has flooded into the bottom compartment. If this happens turn the bubbler upside down and blow into the air hole at the bottom to clear this section. Then re-fill from the top. 

Place bubbler onto Core 2.0 Base at an angle, ensuring that the hole in the bubbler base aligns with the vapor pathway in the Core 2.0 base, then gently and firmly push it straight down into place. 

Check small screws in the atomizer base which hold the heater legs are done up fully. These need to be tightened so they are firm, but not so much that they cut the wire legs off the heater. When this is done screw the atomizer into the Core 2.0 base. 

Place the carb cap tube on the base so that the wider angled side sits at the top, leaving the carp cab on the tether so that you can load concentrate onto the heater. 
Select your desired heat setting (start low if you’re not sure). 

Now that’s all done we get onto the vaping methods as there are different ways the Core 2.0 can be used! 
 
 
Methods of Use 
 
Cold Starts – This method is best for getting the most flavor and material preservation as you start using as soon as vapor is being produced. Using it in this way will cause the session temperatures to be slightly lower than otherwise because the air passing around the heater will decrease heating speed. You can start your session at any point, we suggest keeping an eye on the button flashes so that you can always begin after a set number of flashes, if desired, providing a very consistent and repeatable experience. 
 
Load material into the heater 
Press the fire button twice to activate session mode 
When your concentrate starts to bubble begin using gently with the carb cap left off 
When the Core 2.0 base vibrates place the carb cap back on and continue your use as you normally would 
For subsequent sessions just use as desired, when the flavor leaves your material, the vapor becomes harsh or stops being produces press the fire button once more to cancel the session 
If you still have material left inside at the end of the session simple hit the fire button twice again and start using immediately, no need to wait for the vibrate as your heater will already be close to adequate temperature. The second session will always run a little hotter than the first if it is started straight after 
Hot Starts –  This way allows the heater to reach full temperature for any given setting; so this method is best for getting the maximum cloud production and effects as quickly as possible. 
 
Press the power button twice to activate session mode 
Load your material onto your dab tool – rice size 
Wait for the Core 2.0 base to vibrate indicating the session temperature has been reached 

While using gently load the dab into the heater, then replace the carb cap and use as your normally would

For subsequent sessions you can carry on as desired. The same applies here with regard to finishing your session. If your material is finished hit the fire button once to cancel the session early, if you still have material left simply hit it twice when the session has ended to start it again! 

As with cold starts, follow up sessions will always run a little hotter. 
Manual – Self explanatory, load a small rice size dab into the heater and hold down the power button. Use as desired. 
 
Manual hold can also be used instead of double pressing to finish a session or heat the heater for easier cleaning. 
 
 
 
Cleaning 
 
Wipe out heater with a Q-tip after each use 
Clean the area around the RDA heater weekly to stop residue building up 
Every month or so wipe out the airway with a Q-tip soaked in ISO – allow to fully dry before use 
Replace bubbler water daily 
To clean bubbler fill with hot water and shake to remove large residues. Soak in ISO to fully clean. Rinse thoroughly with warm water after soaking. 
 
 
Safety Features 
 
Over-charge 
Over-discharge/Low battery 
Over-heat 
Low heater resistance 
Short-circuit 
No atomizer 
 
 
Certifications 
 
CE Certified 
ROHS Certified Materials 
FCC Certification 
FDA Approved Silicone 
UN 38.3 Certified Li-Ion Battery Pack. 
Warning Lights – When your Core 2.0 base flashes three times it’s trying to tell you something… 
 
Blue – Short-circuit warning 
Green – No atomizer warning 
White – Over-heat warning 
Red – Low battery warning 
  
Warranty information 
 
For all warranty claims please contact the store you purchased from. 
The Core 2.0 power base is covered by a one year manufacturer warranty against defects. 
The Core 2.0 carry case is covered by a one year manufacturer warranty against defects. 
The atomizer is covered by a one week manufacturer warranty against defects. 
While atomizers are expected to last much longer than one week, they can be damaged by mishandling and misuse. We understand that not everyone will use the device daily or immediately so offer a one week warranty, from the date of delivery, to report any issue with your atomizer. 

Crossing Core 2.0 | 2.1 Recycling Bubbler E-Rig Kit

Bomb Pro Portable Electric E-Rig

Bomb Pro E-rig is designed for dab enthusiasts. The led display shows the Precise Temperature from 400 -700 ℉ in real time. Colorful pulsing and glowing light strips, responding to your every dab. Make your way of dabbing easier with one button control.
Rips are ripping no matter what the temperature is; unique memory function can remember your favorite temperature mode, click 3 times quickly to enter the temperature adjustment mode and set the temperature you want, this will be the temperature limit in your dabbing process, so as to ensure the flavor you want most.
Fits perfectly in your hand, enjoy this device everywhere, perfect for daily dabbing enthusiasts.
If you are the first time to use Bomb pro electric dab rig, no need to worry, easy solid feel to it. You will be Obsessed with the device, definitely give you huge clouds and best flavor.
Cleaning up is a breeze – both the glass and atomizer are removable. The ceramic coil is easily cleaned with cotton swabs, ensure a hassle-free routine for your next happy session.
The glass bubbler can be interchanged with any Puffco Peak glass models!
Add the extra atomizer option to save!
What's Included
Bomb Pro Device * 1
Bomb Pro Atomizer * 1
Dab Tool * 1
USB-C Cable * 1
Cotton Swab
Filling Tool * 1
Bomb Protection & Warranty
The Bomb Pro is covered for 90 days under the Bomb warranty.

Bomb Pro Portable Electric E-Rig

Crossing Core XL Kit
THE BRAND NEW CROSSING TECH CORE XL VAPORIZER IS HERE! A newly updated base with 6 heat settings, new XL atomizer, and new Grenade Glass bubbler!

The Core has been updated, to it's core! The new eRig has a brand new power base with 6 heat settings, a new high-flow glass percolator, and is fitted with the 3D XL atomizer! The carb cap and holder have also been modified for the new device. 

The Core XL E-rig is the latest portable e-rig from SZ Crossing A.K.A. CrossingTech. It is an all in one dab rig designed for use with a full range of concentrates, from thin oils to solid shatter style material. With a solid build made from high quality materials, a fully heated large capacity cup, vortex airflow and everything you need to get started (except concentrates) it provides the best entry level e-rig experience. After a little practice it rivals much more expensive devices! 

Atomizer Choices:
-Core XL with Non-Rebuildable Heater
With these you can replace the whole atomizer, the heater is fixed inside. They have been made since some people have no desire to replace heaters in housings so this more convenient solution exists

-Core XL with Rebuildable Heater
With these you can replace the ceramic heaters, ceramic spacers, and screws. This is a better option for technical individuals that like to tear down and rebuild their atomizers for a more hands on approach. 


Features

Core XL runs XL 3D Ceramic heaters only, no wire based coils
Atomizers contain only Metal and Ceramic, silicone and PEEK has been replaced with an all ceramic design
Six Heat settings
Increased total session time (80 second full run time)
Vortex airflow - included updated spinner carb cap
"Unbreakable" aluminium carb cap 
Improved button function
Upgraded Stainless Steel Carb Cap Tube
One button functionality for ease of use
Fully heated high polish ceramic vaping surface - elements inside base and walls of heater
Rebuildable or non-rebuildable atomizer options 
Borosilicate Glass Bubbler Grenade Bubbler - an upgrade over previous Core bubblers 
Updated Stainless Steel Carb Cap Tube and heat dissipator
Isolated Anodized Aluminium and Glass Vapor Pathway
Low maintenance 
Approx. 1 hour 45 minute charging time
3150mah Li-Ion Battery Pack
Approx. 21 full sessions - mixed power settings 
 

What's Included

Core XL E-rig Base with six heat settings
Core Grenade bubbler with better function and angled mouthpiece
Aluminum Spinner Carb Cap
Carb Cap Tether (black)
Silicone Base Cover/Sleeve (black)
Core XL 3D Ceramic Atomizer
SS316 Dab Tool
2 x Spare Carb Cap Tube O-rings
1 x USB-C Charging Cable
Cotton buds/Q-tips
Alcohol wipes 
Carry Case
 

Button Function

Two clicks - Activate session mode - One click to cancel
One Clicks - Change heat setting 
Four Click - Display power level - Red/Low - White/Medium - Green/Full
Five Clicks - Lock or unlock device
 

Sessions times and temperatures

The total session time for the Core XL has been upgraded to 80 seconds, this includes the pre-heat time. It now has 6 heat settings, click once to cycle through these. 

Purple / Lowest - 320f after preheat 
Yellow / Second lowest - 330f after preheat 
Blue / Middle - 350f after preheat
Green / Middle high - 395f after preheat
White / Second highest - 450f after preheat
Red / Highest - 500f after preheat
 

Setup

Always hold your e-rig upright! If you angle it during use concentrate will spill out the bucket! Now that's out the way...
Charge your base using the provided wall plug and cable. 
Fill the bubbler from the top, when it is removed from the base. Ensure any excess liquid has been wiped away and that no water has flooded into the bottom compartment. If this happens turn the bubbler upside down and blow into the air hole at the bottom to clear this section. Then re-fill from the top. 
Do not fill the bubbler past 1/4 fill height or you risk flooding the base and damaging the unit. Just above the airflow slits inside is fine.
When replacing the bubbler, place it on the base at an angle, ensuring that the hole in the bubbler base aligns with the vapor pathway, then gently and firmly push it straight down into place. 
For Rebuldable Atomizer check the small screws in the atomizer base which hold the heater legs are done up fully. These need to be tightened so they are firm, but not so much that they cut the wire legs off the heater. 
Select your desired heat setting (start low if you're not sure).
 

Vaping methods

Cold Starts - This method is best for getting the most flavour and material preservation as you start inhaling as soon as vapour is being produced. Vaping in this way will cause the session temperatures to be slightly lower than otherwise because the air passing around the heater will decrease heating speed.  You can start your inhale at any point, we suggest keeping an eye on the button flashes so that you can always begin inhaling after a set number of flashes, if desired, providing a very consistent and repeatable experience. 

Load a rice grain size dab (basmati not long grain) into the heater
Press the fire button twice to activate session mode
When your concentrate starts to bubble begin inhaling gently with the carb cap left off
When the Core 2.0 base vibrates place the carb cap back on and continue your inhale as you normally would
For subsequent inhalations just inhale as desired, when the flavour leaves your material, the vapor becomes harsh or stops being produces press the fire button once more to cancel the session
If you still have material left inside at the end of the session simple hit the fire button twice again and start vaping immediately, no need to wait for the vibrate as your heater will already be close to vaping temperature. The second session will always run a little hotter than the first if it is started straight after
It's been advised by the manufacturer to avoid doing hot starts where the dab is loaded into a pre-heated heater as this can crack the ceramic due to the temperature difference
Manual - Self explanatory, load a small rice size dab into the heater and hold down the power button. Inhale as desired. 

Manual hold can also be used instead of double pressing to finish a session or heat the heater for easier cleaning. 

 

Cleaning

Wipe out heater with a q-tip after each use
Clean the area around the atomizer weekly to stop residue building up
Every month or so wipe out the airway with a q-tip soaked in ISO - allow to fully dry before use
Replace bubbler water daily
To clean bubbler fill with hot water and shake to remove large residues. Soak in ISO to fully clean. Rinse thoroughly with warm water after soaking.  
The Core Atomizer can also be removed and screwed into a heat sink on our Pico Plus with auto-fire or an Arctic Fox or DNA-C box mod (with auto-fire), then run at 36W upside down for 1-2 mins to perform a burn off cycle to clean the heater back to new. This is optional. You can also use the CUB instead of a heat sink with this setup, the CUB can also be used with the atomizers as a standalone portable when paired with a box mod such as the Pico Plus. 
 

Safety Features 

Over-charge 
Over-discharge/Low battery
Over-heat 
Low heater resistance
Short-circuit 
No atomizer 
 

Certifications

CE Certified
ROHS Certified Materials
FCC Certification
FDA Approved Silicone
UN 38.3 Certified Li-Ion Battery Pack. 
 

Warning Lights - When your Core 2.0 base flashes three times it's trying to tell you something...

Blue - Short-circuit warning
Green - No atomizer warning
White - Over-heat warning
Red - Low battery warning
 

Warranty information

For all warranty claims please contact the store you purchased from.
The Core XL power base is covered by a one year manufacturer warranty against defects.
The atomizer is covered by a one week manufacturer warranty against defects, this can be damaged by aggressive cleaning or accidental damage from tools.
While atomizers are expected to last much longer than one week, they can be damaged by mishandling and misuse. We understand that not everyone will use the device daily or immediately so offer a one week warranty, from the date of delivery, to report any issue with your atomizer.

Note: older coils and RDAs from the Core and Core2 will work on the new Core XL.



Crossing Core XL Kit

Crossing Core 2.1 E-Rig Kit  

The Crossing Core 2.1 is a significant upgrade over the Crossing Core 2.0 in several key areas. Firstly, the Core 2.1 features a more powerful 3150mAh battery, providing longer and more consistent performance compared to the Core 2.0. This means that you won't have to worry about running out of power during your dabbing sessions.
 


Non Rebuildable 3D Atomizer

The Core 2.1 features a non rebuildable 3D atomizer which will provide a much higher overall quality. It also removes the need for the tools required to dismantle and put together the Atomizer. Shenzhen Crossing understood that most consumers look for relaxation when vaporizing and the extra rebuild step is simply not worth it. They've been designed for people who aren't comfortable rebuilding their setups. Simply unscrew the old and screw in the new!

* Direct Heat from the Ceramic Bucket
* Ceramic and Stainless Steel Build
* Larger Vapor and Better Taste
* Quicker Warm-up
* Exchangeable

Another major improvement in the Core 2.1 is its precision temperature control system, which allows you to set your desired temperature with greater accuracy. The newest version features 4 temperature settings that are indicated by a color. This results in a much more consistent and enjoyable dabbing experience, as you are able to fine-tune the temperature for your specific concentrates and oils.


Here are the major key differences between the Core and Core 2.1 e-rigs which are as follows: 
 
Core 2.1 runs a rock solid nonrebuildable 3D atomizer, no wire based coils 
Atomizers contain only Metal and Ceramic, silicone and PEEK has been replaced with an all ceramic design 
larger 3150mAh battery
Four heat settings are now all for the 2.1 3D atomizer 
Decreased pre-heat time 
Increased session time 
Increased total run time (80 second full run time) 
Improved button function 
 
 
Core 2.1 Features:
 
One button functionality for ease of use 
Fully heated high polish ceramic vaping surface – elements inside base and walls of heater 
Non-Rebuildable atomizer 
Vortex Airflow – Aluminum spinner carb cap with carb cap tether 
Borosilicate Glass Bubbler 
Stainless Steel Carb Cap Tube 
Four carefully tuned heat settings 
Isolated Aluminum and Glass Vapor Pathway 
Low maintenance 
Approx. 1 hour 45 minute charging time 
3150mah Li-Ion Battery Pack. 
 
 
What’s Included:
 
Core 2.1 E-rig Base 
Core Bubbler 
Aluminum Spinner Carb Cap (based on our design) 
Carb Cap Tether (black) 
Silicone Base Cover/Sleeve (black) 
2.1 3D Atomizer
SS316 Dab Tool (based on our design) 
2 x Spare Carb Cap Tube O-rings 
1 x Wall Plug – US inside – UK included for UK orders 
1 x USB-C Charging Cable 
Cotton buds/Q-tips 
Alcohol wipes 
Upgraded Carry Case 
 
 
Button Functions:
 
Hold – Manual fire up to 60 seconds 
Two clicks – Activate session mode – One click to cancel 
Three Clicks – Change heat setting 
Four Click – Display power level – Red/Low – White/Medium – Green/Full 
Five Clicks – Lock or unlock Core 2.1 Base 
 
 
Sessions times and temperatures 
 
The total session time for the Core 2.1 has been upgraded to 80 seconds, this includes the pre-heat time. 
 
Blue – 12.5 second pre-heat – Approx. 205°C
Green – 13 second pre-heat – Approx. 220° 
White – 17.5 second pre-heat – Approx. 240° 
Red – 22.5 second pre-heat – Approx. 260° 
 
 
Setup 
 
Charge your base using the provided wall plug and cable. 
Fill the bubbler from the top, when it is removed from the base. Ensure any excess liquid has been wiped away and that no water has flooded into the bottom compartment. If this happens turn the bubbler upside down and blow into the air hole at the bottom to clear this section. Then re-fill from the top. 

Place bubbler onto Core 2.1 Base at an angle, ensuring that the hole in the bubbler base aligns with the vapor pathway in the Core 2.1 base, then gently and firmly push it straight down into place. 

Check small screws in the atomizer base which hold the heater legs are done up fully. These need to be tightened so they are firm, but not so much that they cut the wire legs off the heater. When this is done screw the atomizer into the Core 2.1 base. 

Place the carb cap tube on the base so that the wider angled side sits at the top, leaving the carp cab on the tether so that you can load concentrate onto the heater. 
Select your desired heat setting (start low if you’re not sure). 

Now that’s all done we get onto the vaping methods as there are different ways the Core 2.1 can be used! 
 
 
Methods of Use 
 
Cold Starts – This method is best for getting the most flavor and material preservation as you start using as soon as vapor is being produced. Using it in this way will cause the session temperatures to be slightly lower than otherwise because the air passing around the heater will decrease heating speed. You can start your session at any point, we suggest keeping an eye on the button flashes so that you can always begin after a set number of flashes, if desired, providing a very consistent and repeatable experience. 
 
Load material into the heater 
Press the fire button twice to activate session mode 
When your concentrate starts to bubble begin using gently with the carb cap left off 
When the Core 2.1 base vibrates place the carb cap back on and continue your use as you normally would 
For subsequent sessions just use as desired, when the flavor leaves your material, the vapor becomes harsh or stops being produces press the fire button once more to cancel the session 
If you still have material left inside at the end of the session simple hit the fire button twice again and start using immediately, no need to wait for the vibrate as your heater will already be close to adequate temperature. The second session will always run a little hotter than the first if it is started straight after 
Hot Starts –  This way allows the heater to reach full temperature for any given setting; so this method is best for getting the maximum cloud production and effects as quickly as possible. 
 
Press the power button twice to activate session mode 
Load your material onto your dab tool – rice size 
Wait for the Core 2.1 base to vibrate indicating the session temperature has been reached 

While using gently load the dab into the heater, then replace the carb cap and use as your normally would

For subsequent sessions you can carry on as desired. The same applies here with regard to finishing your session. If your material is finished hit the fire button once to cancel the session early, if you still have material left simply hit it twice when the session has ended to start it again! 

As with cold starts, follow up sessions will always run a little hotter. 
Manual – Self explanatory, load a small rice size dab into the heater and hold down the power button. Use as desired. 
 
Manual hold can also be used instead of double pressing to finish a session or heat the heater for easier cleaning. 
 
 
 
Cleaning 
 
Wipe out heater with a Q-tip after each use 
Clean the area around the RDA heater weekly to stop residue building up 
Every month or so wipe out the airway with a Q-tip soaked in ISO – allow to fully dry before use 
Replace bubbler water daily 
To clean bubbler fill with hot water and shake to remove large residues. Soak in ISO to fully clean. Rinse thoroughly with warm water after soaking. 
 
 
Safety Features 
 
Over-charge 
Over-discharge/Low battery 
Over-heat 
Low heater resistance 
Short-circuit 
No atomizer 
 
 
Certifications 
 
CE Certified 
ROHS Certified Materials 
FCC Certification 
FDA Approved Silicone 
UN 38.3 Certified Li-Ion Battery Pack. 
Warning Lights – When your Core 2.1 base flashes three times it’s trying to tell you something… 
 
Blue – Short-circuit warning 
Green – No atomizer warning 
White – Over-heat warning 
Red – Low battery warning 
  
Warranty information 
 
For all warranty claims please contact the store you purchased from. 
The Core 2.1 power base is covered by a one year manufacturer warranty against defects. 
The Core 2.1 carry case is covered by a one year manufacturer warranty against defects. 
The atomizer is covered by a one week manufacturer warranty against defects. 
While atomizers are expected to last much longer than one week, they can be damaged by mishandling and misuse. We understand that not everyone will use the device daily or immediately so offer a one week warranty, from the date of delivery, to report any issue with your atomizer. 

Discount E-Nails

Vape pens, THC pens, batteries, & weed vaporizers